New Holland Hay Equipment 1411 Parts

CNH Direct Ship
Discbine Knives
CCW 7 DEGREE TWIST (Type 1)
Part #9847684
$1.85
CW 7 DEGREE TWIST
Part #9847683
$1.85
Kit of 16CW/16CCW - Type 2
Part #86624752
$52.00
Crop Lifter Kit
Part #87528245
$116.50
Cross and Bearing Kit
Part #86520896
$47.87
Cutting Knife Kit
Part #86624751
$33.00
CCW 14 DEGREE TWIST KNIVES
Part #86621873
$1.85
Discbine Parts and Maintenance
CW MODULE ASSEMBLY
Part #84220789
CW
$373.70
STONEGUARD
Part #87044117
$25.88
DISC MOWER ROCKGUARD KIT
Part #87297019
$51.49
SKID SHOE KIT
Part #87297018
$75.59
(#6) TOP CAP ASSEMBLY
Part #87753841
$257.55
Shock Pro Repair Kit
Part #87580643
$47.61
DISC
Part #87646406
$74.31
(#7) Lifter Kit (CCW)
Part #87528249
$116.50
Short Shaft (248mm)
Part #86519042
$59.96
Top Cap w/Shock Pro
Part #87753842
$241.39
Grease Guns
14oz High-Temp Grease
Part #9861804DS
$4.50
New Holland
HUB
Part #84195890
$56.38
Uncategorized Parts
SMV METAL
Part #2000884
$11.99
SLINGER
Part #86515894
$3.75
NUT G8 P -75
Part #86518194
$1.45
BUSHING
Part #365820
$35.51
CCW Module Gear Box
Part #84220790
$373.70
SEAL
Part #86511201
$9.21
HEX FLNG SCRW
Part #86515926
$3.03
SCREW
Part #86600611
$6.38
NUT
Part #87725066
$5.14
SKID/SHOE
Part #87047426
$39.85
BEARING, BALL
Part #86575514
$82.00
BOLT ASSEMBLY
Part #86571960
$44.25
SPECIAL NUT
Part #86557260
$8.88
CROSS & BEARING
Part #86551252
$206.04
HEX FLNG SCRW
Part #86515925
$2.78
TIE BOLT
Part #86501934
$15.90
BUSHING
Part #87659928
$32.86
BOLT
Part #87584169
$5.63
BOLT
Part #87040886
$2.78
SPACER
Part #86573045
$10.93
HYD RPR KIT
Part #792803
$45.54
1411 OP MANUAL
Part #87548184
$36.83
1411 PARTS BOOK
Part #87516909
$42.15
1411 SERVICE
Part #86630282
$93.42
ARM ASSY.
Part #87057901
$388.85
BEARING HOUSING
Part #86573043
$141.06
CAP
Part #86633618
$150.47
HUB
Part #86629692
$44.60
KIT, SEALS
Part #86539474
$15.90
LH Mounting Spacer
Part #87057898
$419.15
NUT
Part #87053834
$5.24
SMV SPADE W/HDWR
Part #2001033
$2.49
SPIDER
Part #84355038
$50.20
V BELT BANDD4
Part #86627791
$125.61

Conditioner Rollers

Type: Rubber

Dimensions

Ground Clearance: 18 inches
Operating Length: 17.2 ft
Operating Width: 16 ft
Transport Height: 5.8 ft
Transport Width: 11.3 ft
Weight: 4100 lbs

Disc Cutter Bar

Disc Speed: 3000
Knives per Disc: 16
Number of Discs: 8

Tractor Requirements

Hitch Category: pull type
PTO HP: 80 HP
PTO Speed: 540
Q: What oil do I use in the Disc Modules?

Messicks uses 80W90 GL4 or GL5 spec. 

answered by mwi on 9/24/2014
Q: How much oil is in the Disc Modules?

They hold 10 oz of 80W90 oil.

answered by mwi on 9/24/2014
Q: When should I change the oil in the modules?

The oil should be changed yearly or every 200 hours, which ever comes first

answered by mwi on 9/24/2014
Q: Can I put a Shock Pro on the Drive end?

No, the Shock Pro can not be used on the drive end.

answered by mwi on 11/19/2014
Q: What oil do I use in the Disc Modules?

Messick's uses 80W90 GL4 or GL5.

answered by BLK on 11/19/2014
Q: How much oil is in the Disc Modules?

They hold approximately 10 OZ of oil.

answered by BLK on 11/19/2014
Q: How often should I change the oil in the modules?

 Every 300 hours or yearly, which ever comes first.

answered by BLK on 11/19/2014
Q: Can I put a Shock Pro Hub on the drive modules?

 No. Shock Pro can not be used on the drive modules.

answered by BLK on 11/19/2014
New Holland mow max bar explination
video showing the parts of the cutterbar and how they work and go together.
Roll Gap Setting
How to set the roll gap properly.
Machine Setup and Wide Thin Kit
Machine operation, and function of the wide thin kit.
Video on tearing down a cutterbar
video on tearing down a cutter bar.