(15 minutes)
I have an L3301 kubota tractor. The floor mat installation was a little tricky. The left side mat was easy to install but the right side with the HST pedal a little tougher. On the right side you definitely have to remove the two small bolts under the HST pedal since they interfere with the hole alignment on the locking tabs on the mat. Where you can't get your hand to pull down the locking tabs on the bottom of the mat because of tractor part interference, use a ball peen hammer to tap the tabs into the holes on the metal floor frame. Push down on the HST pedal to provide clearance to tap the tabs down.
.
11/6/2023 Broadview Heights, OH John
(5 minutes)
10/13/2023 NEWBORN, GA Mark
(10 minutes)
Installed on L3400 required minor trimming.
4/28/2023 COWLESVILLE, NY John
(10 minutes)
Super easy to install. I took a few minutes to wash and dry the metal floorboards to ensure they were clean before installing to minimize additional wear and/or corrosion. I used a bit of water with some dish soap in it to lubricate the rubber studs that go into the floorboard holes to hold the mat in position. A great add to my L2501!
4/7/2023 Choctaw, OK LEE
(5 minutes)
Holes in the mat doesn’t line up with the pedal limiter.
4/5/2023 SHANNON, NC Wiley
3/16/2023 INGRAHAM, IL Leon
(15 minutes)
3/1/2023 SUPPLY, NC Jason
Unrated
(10 minutes)
A little soap onpull tabs makes so much easier.
2/27/2023 GROVE, OK DOC
Unrated
(10 minutes)
Touch up the worn floor plates before placing the floor mats. I have found that Chevy orange engine paint is a perfect match for Kubota orange. Spray the rubber tits with soapy water and they easily pull through.
2/16/2023 BRIGHTON, CO RICHARD
(10 minutes)
I used a pair of offset needlenose pliers to reach into the tight spots to help pull the rubber keepers into the floorboard holes.
2/16/2023 WARREN CENTER, PA JOHN
(5 minutes)
2/3/2023 ELWOOD, IN Bradley
(15 minutes)
1/20/2023 SOCIAL CIRCLE, GA CHANDLER
(5 minutes)
Simple straightforward install. No need to remove pedal. I did remove the forward and reverse travel stop bolts. A little dish soap on the rubber tabs helps the install as well.
12/20/2022 ORANGE, CT Joseph
(5 minutes)
12/14/2022 ASHLAND, KY Dwayne
Unrated
Once I got the first couple lined up and started popping them in even though the temperature was in the 30s they popped in and I had no problem jumped on my tractor and did not slip
12/12/2022 HESPERIA, MI Dorothy
(1 minute)
I sprayed a little soapy water on the back and pushed the plugs through the holes from the top. Too easy
11/18/2022 VICKSBURG, MS Glenn
11/17/2022 Hastings, MN Jerry
Unrated
(2 minutes)
11/4/2022 Chatsworth, GA A&R
Just put a drop of dawn dishwashing liquid on the little pegs, line up in the correct holes and push right in from the top. Easy as it can be. Looks great!!!
10/27/2022 BENTON, KY Michael
Unrated
Pedal stop bolts both come out when installing mats and do not go back in . Makes install easier without bolts as well.
10/17/2022 SAINT ALBANS, VT Darren
Unrated
Spray with Pam cooking spray
9/8/2022 Floyds Knobs, IN Bill
Unrated
(20 minutes)
Use soapy water on the rubber tips and guide them into the floor holes before pressing down on the mat to push the tips into place.
9/1/2022 Clinton, MS David
Unrated
(3 minutes)
Simple line up pull through
8/29/2022 WEST MONROE, LA Raymond
Unrated
I sprayed each of the “plugs” on the back of the mat with silicone lubricant. They snapped right into the matching hole on the floor plate.
Higden, AR
Scott