New Holland Hay Equipment H7220 Parts

CNH Direct Ship
Wheel Bearing Kit
Part #87298554
$39.33
1 Gal SAE 80W-90 Gear Lube
Part #B80902
$21.40
Discbine Knives
CCW 7 DEGREE TWIST (Type 1)
Part #9847684
$1.85
CW 14 Degree Serrted Knives
Part #87029587
$3.65
CW 7 DEGREE TWIST
Part #9847683
$1.85
V-Knife / Rock Knives
Part #86532078
$3.35
Crop Lifter Kit
Part #87528245
CW
$116.50
CCW 14 Degree Serrted Knives
Part #87029588
$3.65
CCW 14 DEGREE TWIST KNIVES
Part #86621873
$1.85
CW 14 DEGREE TWIST KNIVES
Part #86621872
$1.85
Discbine Parts and Maintenance
CW MODULE ASSEMBLY
Part #84220789
$373.70
STONEGUARD
Part #87044117
$25.88
DISC MOWER ROCKGUARD KIT
Part #87297019
$51.49
(#6) TOP CAP ASSEMBLY
Part #87753841
$257.55
Shock Pro Repair Kit
Part #87580643
$47.61
DISC
Part #87646406
$74.31
(#7) Lifter Kit (CCW)
Part #87528249
$116.50
Short Shaft (248mm)
Part #86519042
$59.96
Long Shaft (268mm)
Part #86519039
$70.73
Top Cap w/Shock Pro
Part #87753842
$241.39
CCW REMAIN MODULE
Part #84220790R
$348.45
CW REMAIN MODULE
Part #84220789R
$348.45
New Holland
HUB
Part #84195890
$56.38
New Holland Hay Parts
Friction Repair Kit
Part #86601404
$125.61
Uncategorized Parts
SMV METAL
Part #2000884
$11.99
CCW Module Gear Box
Part #84220790
$373.70
SEAL, WIPER
Part #87025444
Lift Slave Cylinder
$20.94
KIT, SEALS
Part #87027481
Lift Master Cylinder
$51.49
SKID/SHOE
Part #87047426
$39.85
SEAL, WIPER
Part #87025441
Tilt Cylinder
$28.20
LAMP
Part #86536572
$55.09
CROSS
Part #84355317
$77.64
DRUM
Part #87040772
$176.75
GEARBOX ASSY
Part #87025403
$2,666.40
High Stub Shoe
Part #87622885
High Stub
$98.91
PTO ASSY, REAR
Part #84139314
$1,463.49
RED LIGHT ASY
Part #86514198
$55.09
REMAN-TRANSMISSI
Part #87025403R
$2,191.70
ROLL
Part #84398514
Upper
$1,711.95
ROLL
Part #84398517
Lower
$2,065.45
SEAL, WIPER
Part #87027952
Tongue Swing
$39.85
SMV SPADE W/HDWR
Part #2001033
$2.49

Conditioner Rollers

Adjustment: Single crank adjustable roll pressure
Diameter: 10.4 in
Drive: 4 HB V-belt & enclosed gears
Length: 90 in
Speed: 647 rpm
Type: Chevron-design intermeshing molded rubber

Dimensions

Operating Height: 4' 5" ft
Operating Length: 17' 2" ft
Operating Weight: 3,690 lbs
Operating Width: 14' 10" ft
Transport Height: 5' 8" ft
Transport Length: 17' 7" ft
Transport Width: 9' 11" ft

Disc Cutter Bar

Cutting Height Adjustment: 0.95 to 3.2 in
Cutting Height Control: mechanical or hydraulic control
Cutting Height Range: 2 to 10 degrees
Disc Speed: 3000 rpm
Knives per Disc: 2
Number of Discs: 7

Tractor Requirements

PTO HP: 65 HP
PTO Speed: 540 rpm
Q: What oil do I use in the Disc Modules?

Messick's uses 80W90 GL4 or GL5.

answered by BLK on 11/19/2014
Q: How much oil is in the Disc Modules?

They hold approximately 10 OZ of oil.

answered by BLK on 11/19/2014
Q: How often should I change the oil in the modules?

 Every 300 hours or yearly, which ever comes first.

answered by BLK on 11/19/2014
Q: Can I put a Shock Pro Hub on the drive modules?

 No. Shock Pro can not be used on the drive modules.

answered by BLK on 11/19/2014
New Holland mow max bar explination
video showing the parts of the cutterbar and how they work and go together.
Roll Gap Setting
How to set the roll gap properly.
Machine Setup and Wide Thin Kit
Machine operation, and function of the wide thin kit.
Video on tearing down a cutterbar
video on tearing down a cutter bar.