$<p>Messicks has over 50,000 Kubota parts in our Mount Joy warehouse. Our computerized inventory system enables us to have stock items packaged and at your door in a moments notice, or we can order in specialized items that may be less commonly used. We have taken the time to categorize frequently used parts so you can easily find common maintenance items for your tractor. If you need help finding specific part numbers call us at <b>877-260-3528</b> or email <a href="\">parts@messicks.com</a>.</p>$

#75536-65400 Hydraulic Control Valve Component

Name: Kubota #75536-65400 Hydraulic Control Valve Component
Brand: Kubota
SKU: 75536-65400
Price: 204.33 USD
Availability: InStock

$204.33

5 In Stock

Weight: 0.45 lbs

Kubota 75536-65400 is a hydraulic control valve component, also referred to as a hydraulic valve part or control valve part, used on selected Kubota loader applications.

This part is shown in the control valve component parts and hydraulic valve sections for selected Kubota LA and LB front loader models, including LA181, LA210, LA211, LA271, LA272, LA301, LA302, LA350A, LA350ST, LA351, LA352, LA401, LA402, LA452S, LA481, LA482, LA513, LA681, LA682, LA723, LA852, LA852-2, LA853, LB400, LB400A, LB402, LB552, and LB702. It is used in both 3-position and 4-position control valve applications where shown in the parts diagram.

element not set

This part fits your tractor

This part fits 28 models

CONTROL VALVE [COMPONENT PARTS][BX1611 3POS C/V]

CONTROL VALVE [COMPONENT PARTS][BX1612 4POS C/V]

CONTROL VALVE [COMPONENT PARTS] [3-C/V]

CONTROL VALVE [COMPONENT PARTS] [4-C/V]

CONTROL VALVE [COMPONENT PARTS][3-POSITION C/V]

CONTROL VALVE [COMPONENT PARTS] [4-POSITION C/V]

CONTROL VALVE [COMPONENT PARTS]

CONTROL VALVE

CONTROL VALVE [COMPONENT PARTS]

More Loader ...

CONTROL VALVE [COMPONENT PARTS]

Installation Tips

Unrated (30 minutes)
I took the valve off the tractor and did the work on a bench. The repair took less than 10 minutes. Use grease to keep the ball bearings in place. The most time was taking it off and on the tractor.

3/6/2025
AVERY, CA
Val

The kit doesn't come with instructions but there is a helpful video at https://www.youtube.com/watch?v=J05vSdYn9qE. Once you see the video, things are pretty obvious. But it's much easier to do the work with the valve off the tractor. One problem is that the kit comes with a spacer washer and if yours doesn't have one, or it does and it flies off when the spring releases, it isn't real obvious where it goes. It sits on top of the cup that's closest to the body of the valve to position the spring properly.

8/24/2023
Prospect Harbor, ME
Roger

(1 minute)
Disassemble, tech spool unscrew needle ball holder from spool reinstall new ball holder insert spring insert large ball put in three small balls on sides put the cup over the three balls with the cup tipped at an angle and push the fourth ball in pushing down on the cup and you’re done don’t forget to put on the bottom spacer bolt retainer and you’re done reassemble ,In reverse of disassembly.

6/10/2023
Hoosick Falls , NY
David

(1 minute)
I removed the entire valve body and things became very easy. I replaced the 4 small balls with the spool out of the valve and pushed the end cap assembly all the way to engage the detent. That made it far safer to handle the spool than if the spool was inside the valve body. Final assembly was just a matter of reattaching the hoses and bolting the valve to the mounting plate. Hope this helps.

6/6/2023
SHELL KNOB, MO
RAYMOND

On my BX22, I had to remove the fel, then remove the entire hydraulic control valve. Careful when removing detention cap as there are 4 small and one larger ball bearings in there. Though you do get new ones in the kit. Good YouTube video on setting the new ball bearings in place, bit tricky but doable. Drill small hole 1/16 or 1/8 in bottom cap to let the water out that often gets in there.

6/27/2022
CHAZY, NY
RICKY

No instructions. The ball bearing bolt is often damaged and difficult to extract I ended up using Screwdriver threw ball bearing holes to unthread. When reinstalling lying Greece is needed to hold ball bearings in place while sliding the coupling over them

6/10/2022
MARCELLUS, NY
JON

Show all 6