This part fits your tractor
This part fits models
Product Specifications
Property | Value | |
---|---|---|
Brand | Kubota |
Installation Tips
(10 minutes)
7/29/2024
SOUTHWEST RANCHES, FL
JAMES
SOUTHWEST RANCHES, FL
JAMES
Unrated
(15 minutes)
Only thing I had to do besides lubing the rubber tabs with WD40, was to remove 2 unused bolts on the foot plate. I have no idea what they are for but didn't see any reason for them being there after looking under the foot plate. Didn't have to cut anything. Fit perfectly.
Only thing I had to do besides lubing the rubber tabs with WD40, was to remove 2 unused bolts on the foot plate. I have no idea what they are for but didn't see any reason for them being there after looking under the foot plate. Didn't have to cut anything. Fit perfectly.
5/1/2024
CONCORD, CA
TIMOTHY
CONCORD, CA
TIMOTHY
(10 minutes)
Best to trim out the back side of each bolt hole location before installation.
Best to trim out the back side of each bolt hole location before installation.
12/29/2023
Higden, AR
Scott
Higden, AR
Scott
(15 minutes)
10/13/2023
NEWBORN, GA
Mark
NEWBORN, GA
Mark
Unrated
(30 minutes)
The Right hand side did not fit because the pre holes cutouts for the 2 bolts” heads are off by a 1/2 inch and I had to trim it. Worked but disappointing I had to cut on my new mats!
The Right hand side did not fit because the pre holes cutouts for the 2 bolts” heads are off by a 1/2 inch and I had to trim it. Worked but disappointing I had to cut on my new mats!
5/19/2023
DIMMITT, TX
Texs
DIMMITT, TX
Texs
(10 minutes)
Installed on L3400 required minor trimming.
Installed on L3400 required minor trimming.
4/28/2023
COWLESVILLE, NY
John
COWLESVILLE, NY
John
(10 minutes)
Super easy to install. I took a few minutes to wash and dry the metal floorboards to ensure they were clean before installing to minimize additional wear and/or corrosion. I used a bit of water with some dish soap in it to lubricate the rubber studs that go into the floorboard holes to hold the mat in position. A great add to my L2501!
Super easy to install. I took a few minutes to wash and dry the metal floorboards to ensure they were clean before installing to minimize additional wear and/or corrosion. I used a bit of water with some dish soap in it to lubricate the rubber studs that go into the floorboard holes to hold the mat in position. A great add to my L2501!
4/7/2023
Choctaw, OK
LEE
Choctaw, OK
LEE
(5 minutes)
Holes in the mat doesn’t line up with the pedal limiter.
Holes in the mat doesn’t line up with the pedal limiter.
4/5/2023
SHANNON, NC
Wiley
SHANNON, NC
Wiley
(15 minutes)
3/1/2023
SUPPLY, NC
Jason
SUPPLY, NC
Jason
Unrated
(10 minutes)
Use a ltle sop on tabs. Makes life .uch esie
Use a ltle sop on tabs. Makes life .uch esie
2/27/2023
GROVE, OK
DOC
GROVE, OK
DOC
(5 minutes)
2/3/2023
ELWOOD, IN
Bradley
ELWOOD, IN
Bradley
(10 minutes)
Used soapy water / windex to allow the rubber cleats to push through the receiving/ mounting holes. Overall super easy installation. Love the product- the tractor looks great and the mats prevent paint from wearing preventing corrosion
Used soapy water / windex to allow the rubber cleats to push through the receiving/ mounting holes. Overall super easy installation. Love the product- the tractor looks great and the mats prevent paint from wearing preventing corrosion
2/2/2023
ADA, MI
Kirt
ADA, MI
Kirt
(5 minutes)
Simple straightforward install. No need to remove pedal. I did remove the forward and reverse travel stop bolts. A little dish soap on the rubber tabs helps the install as well.
Simple straightforward install. No need to remove pedal. I did remove the forward and reverse travel stop bolts. A little dish soap on the rubber tabs helps the install as well.
12/20/2022
ORANGE, CT
Joseph
ORANGE, CT
Joseph
(2 minutes)
They are pretty much just lay in place, super easy to install, I am not sure why they didn’t leave a hole for the transmission pedal stop bolts.
They are pretty much just lay in place, super easy to install, I am not sure why they didn’t leave a hole for the transmission pedal stop bolts.
12/14/2022
ASHLAND, KY
Dwayne
ASHLAND, KY
Dwayne
Unrated
Installed while the tractor was in 30° weather as were the mats, but once I started popping them in the holes it worked fine. Hopped in the driver's seat had no problem with my feet slipping
Installed while the tractor was in 30° weather as were the mats, but once I started popping them in the holes it worked fine. Hopped in the driver's seat had no problem with my feet slipping
12/12/2022
HESPERIA, MI
Dorothy
HESPERIA, MI
Dorothy
Good quality and Installation was very easy. My only concern is the cutout holes for the treddel pedal do not line up with the stop screws under the pedal.
11/17/2022
Hastings, MN
Jerry
Hastings, MN
Jerry
Just put a drop of dawn dishwashing liquid on the little pegs, line up in the correct holes and push right in from the top. Easy as it can be. Looks great!!!
10/27/2022
BENTON, KY
Michael
BENTON, KY
Michael
(20 minutes)
Some of the pull pins are line up with step supports and are harder to pull through
Some of the pull pins are line up with step supports and are harder to pull through
10/17/2022
SAINT ALBANS, VT
Darren
SAINT ALBANS, VT
Darren
Unrated
(45 minutes)
Remove the HST Petal and the two petal stop bolts before beginning the installation.
Remove the HST Petal and the two petal stop bolts before beginning the installation.
9/1/2022
Clinton, MS
David
Clinton, MS
David
Unrated
Same as anove
Same as anove
8/29/2022
Sullivan , MO
Dallas
Sullivan , MO
Dallas
Put tabs in holes and pull them from the both until they seat.
8/28/2022
Manitowoc, WI
Scott's
Manitowoc, WI
Scott's
A little soapy water lubricates the rubber knobs that must be pulled through the deck, wich allows much easier installation. Remove treadle pedal stop bolts before installation. --Do not need to replace
8/27/2022
Jamestown, IN
Burks
Jamestown, IN
Burks
(5 minutes)
Remove and discard the treadle pedal stop bolts before installation. They are no longer needed due to the thickness of the rubber mat.
Remove and discard the treadle pedal stop bolts before installation. They are no longer needed due to the thickness of the rubber mat.
8/27/2022
Mathews, AL
Jon
Mathews, AL
Jon
Unrated
(15 minutes)
8/27/2022
Oakboro, NC
Lionel
Oakboro, NC
Lionel
Show all 25

1:24 Ben Rhodes 2023 NASCAR Champion Diecast Truck
Part# T992324KUBBRCHA
15
in Stock
$54.95

1:64 1982 Dodge Ram D350 Dually - Construction Yellow
Part# 46150-B
6
in Stock
$7.99

Kubota Parking Only Embossed Aluminum Sign
Part# KB09-3344
79
in Stock
$18.95

Kubota Pro Chino/Mesh Cap
Part# 2002234850001
100+
in Stock
$11.95

Kubota Navy Denim w/ Tan Mesh Cap
Part# KT19A-H392
100+
in Stock
$17.95

Kubota Micro Mink Sherpa Blanket
Part# KT21E-A633
10
in Stock
$39.95

Kubota Tire Tread Keytag
Part# KT23A-A958
88
in Stock
$3.95

1:64 Ben Rhodes 2022 Kubota ARC NASCAR Truck Diecast
Part# T992265KUBBR
65
in Stock
$7.99

Kubota Navy Denim Leather Patch Cap
Part# C22-09384
16
in Stock
$15.95

Kubota Decal
Part# K2771-65122
41
in Stock
$2.75

Kubota / Messick's Keytag
Part# KT18A-A318
100+
in Stock
$2.95

1:64 Ross Chastain 2024 Kubota ARC Diecast
Part# CX12465KUBRZ
100
in Stock
$12.99

Kubota 50th Anniversary Limited Edition Book
Part# CUKT22C-A852
53
in Stock
$49.95

Kubota Tractor Parking Only Sign
Part# 2004434860001
13
in Stock
$21.95

Kubota / Ross Chastain # 1 Square Black T-Shirt - XL
Part# RCK1002-4
4
in Stock
$24.95

Messick's / Kubota Black Cap
Part# MFEKUBOTACAP
100+
in Stock
$8.99

1:24 Ross Chastain 2024 Kubota Color Chrome ARC Diecast
Part# CX12423KUBRZCL
10
in Stock
$89.95

Kubota / Messick's KeyTag
Part# 2002243220001
79
in Stock
$2.50

Kubota Tri-Color One Flag One Land Cap
Part# KT23A-H914
9
in Stock
$17.95

Kubota 50th Anniversary 20oz Mug
Part# 2004159930001
6
in Stock
$21.95

Kubota Two Tone Chino Cap
Part# 2002234890001
100+
in Stock
$11.95

Messick's Wheel Spinner
Part# MFESPINNER
100+
in Stock
$8.99

Kubota Felt Pennant - Farm Scene
Part# KT23A-A961
14
in Stock
$12.95

Kubota Grey Patch cap w/ Black Mesh
Part# C22-11006
13
in Stock
$17.95

Kubota Magnetic Parts Tray
Part# 77700-02476
79
in Stock
$4.01

1:24 Ben Rhodes 2023 NASCAR Champion Diecast Truck
Part# T992324KUBBRCHA
15
in Stock
$54.95

1:64 1982 Dodge Ram D350 Dually - Construction Yellow
Part# 46150-B
6
in Stock
$7.99

Kubota Parking Only Embossed Aluminum Sign
Part# KB09-3344
79
in Stock
$18.95

Kubota Pro Chino/Mesh Cap
Part# 2002234850001
100+
in Stock
$11.95

Kubota Navy Denim w/ Tan Mesh Cap
Part# KT19A-H392
100+
in Stock
$17.95

Kubota Micro Mink Sherpa Blanket
Part# KT21E-A633
10
in Stock
$39.95

Kubota Tire Tread Keytag
Part# KT23A-A958
88
in Stock
$3.95

1:64 Ben Rhodes 2022 Kubota ARC NASCAR Truck Diecast
Part# T992265KUBBR
65
in Stock
$7.99

Kubota Navy Denim Leather Patch Cap
Part# C22-09384
16
in Stock
$15.95

Kubota Decal
Part# K2771-65122
41
in Stock
$2.75

Kubota / Messick's Keytag
Part# KT18A-A318
100+
in Stock
$2.95

1:64 Ross Chastain 2024 Kubota ARC Diecast
Part# CX12465KUBRZ
100
in Stock
$12.99

Kubota 50th Anniversary Limited Edition Book
Part# CUKT22C-A852
53
in Stock
$49.95

Kubota Tractor Parking Only Sign
Part# 2004434860001
13
in Stock
$21.95

Kubota / Ross Chastain # 1 Square Black T-Shirt - XL
Part# RCK1002-4
4
in Stock
$24.95

Messick's / Kubota Black Cap
Part# MFEKUBOTACAP
100+
in Stock
$8.99

1:24 Ross Chastain 2024 Kubota Color Chrome ARC Diecast
Part# CX12423KUBRZCL
10
in Stock
$89.95

Kubota / Messick's KeyTag
Part# 2002243220001
79
in Stock
$2.50

Kubota Tri-Color One Flag One Land Cap
Part# KT23A-H914
9
in Stock
$17.95

Kubota 50th Anniversary 20oz Mug
Part# 2004159930001
6
in Stock
$21.95

Kubota Two Tone Chino Cap
Part# 2002234890001
100+
in Stock
$11.95

Messick's Wheel Spinner
Part# MFESPINNER
100+
in Stock
$8.99

Kubota Felt Pennant - Farm Scene
Part# KT23A-A961
14
in Stock
$12.95

Kubota Grey Patch cap w/ Black Mesh
Part# C22-11006
13
in Stock
$17.95

Kubota Magnetic Parts Tray
Part# 77700-02476
79
in Stock
$4.01
Other Kubota Parts & Accessories

Kubota Filters

RTV Accessories

Kubota Paint

Kubota Filter Kits

RTV Accessories (X-Series)

Aftermarket Kubota RTV Accessories

Kubota Block Heaters

RTV SideKick Accessories

Kubota Keyless Start

Kubota Tractor Accessories

Brush Guard Inserts

Kubota Turf/Landscape Accessories

Kubota Construction Accessories

Loader Storage Tubes

Hydraulic Rear Remote Valves

Kubota Tires
Other Kubota Parts & Accessories

Kubota Filters

RTV Accessories

Kubota Paint

Kubota Filter Kits

RTV Accessories (X-Series)

Aftermarket Kubota RTV Accessories

Kubota Block Heaters

RTV SideKick Accessories

Kubota Keyless Start

Kubota Tractor Accessories

Brush Guard Inserts

Kubota Turf/Landscape Accessories

Kubota Construction Accessories

Loader Storage Tubes

Hydraulic Rear Remote Valves

Kubota Tires
Videos

Fits on my L2501 but the holes for the stops for the HST pedal are not in the right location so I will have to put holes in the correct spot.
BIG LAKE, MN
Napoleon